Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC U1A4B:43/U1A4B:44/U1A4B:45/U1A4B:46/U1A4B:47/U1A4B:48/U1A4B:49/U1A4B:96 [BLIND SPOT MONITORING (BSM) CONTROL MODULE]

< Previous Next >

2016 – MX-5 – i-ACTIVSENSE

DTC U1A4B:43/U1A4B:44/U1A4B:45/U1A4B:46/U1A4B:47/U1A4B:48/U1A4B:49/U1A4B:96 [BLIND SPOT MONITORING (BSM) CONTROL MODULE]

CAUTION:

  • When replacing a blind spot monitoring (BSM) control module (RH) having any of the following part numbers, it is necessary to replace the blind spot monitoring (BSM) control module (LH) at the same time to perform the configuration normally.

    • N243-67Y80 A

    • N243-67Y80 B

    • N243-67Y80 C

Description

Blind spot monitoring (BSM) control module (RH) malfunction

Detection condition

  • U1A4B:43

    • Blind spot monitoring (BSM) control module (RH) external RAM malfunction detected with the ignition switched ON (engine off or on).

  • U1A4B:44

    • Blind spot monitoring (BSM) control module (RH) internal RAM malfunction detected with the ignition switched ON (engine off or on).

  • U1A4B:45

    • Blind spot monitoring (BSM) control module (RH) ROM malfunction detected with the ignition switched ON (engine off or on).

  • U1A4B:46

    • Blind spot monitoring (BSM) control module (RH) EEPROM malfunction detected with the ignition switched ON (engine off or on).

  • U1A4B:47

    • Blind spot monitoring (BSM) control module (RH) monitoring system malfunction detected with the ignition switched ON (engine off or on).

  • U1A4B:48

    • Blind spot monitoring (BSM) control module (RH) communication circuit malfunction detected with the ignition switched ON (engine off or on).

  • U1A4B:49

    • Blind spot monitoring (BSM) control module (RH) voltage control circuit malfunction detected for 1 s or more with the ignition switched ON (engine off or on).

  • U1A4B:96

    • Blind spot monitoring (BSM) control module (RH) internal circuit malfunction detected for 1 s or more with the ignition switched ON (engine off or on).

Fail-safe

  • U1A4B:43

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:44

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:45

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:46

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:47

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:48

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:49

    • Blind spot monitoring (BSM) system is stopped.

  • U1A4B:96

    • Blind spot monitoring (BSM) system is stopped.

Possible cause

  • Blind spot monitoring (BSM) control module (RH) malfunction

System wiring diagram

Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

 VERIFY IF MALFUNCTIONING LOCATION IS BLIND SPOT MONITORING (BSM) CONTROL MODULE (RH) DEPENDING ON REPEATABILITY

Yes

Replace the blind spot monitoring (BSM) control module, then go to the next step.

(See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION.)

No

Go to the next step.

2

 VERIFY IF OTHER DTCs DISPLAYED

  • Are any other DTCs displayed?

Yes

Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.

(See DTC TABLE [BLIND SPOT MONITORING (BSM) CONTROL MODULE].)

No

DTC troubleshooting completed.

< Previous Next >

© 2014 Mazda North American Operations, U.S.A.