Description

Communication error with auxiliary jack/USB port/SD card slot hub

Detection condition

• With the ignition switched ON (engine off or on), the connectivity master unit (CMU) cannot receive a signal from the auxiliary jack/USB port/SD card slot hub.

Fail-safe

Not applicable

Possible cause

• Auxiliary jack/USB port/SD card slot hub connector or terminal malfunction

• Connectivity master unit (CMU) connector or terminal malfunction

• Open circuit in wiring harness between the following terminals:

• Connectivity master unit (CMU) terminal 4B—Auxiliary jack/USB port/SD card slot hub terminal 2B

• Connectivity master unit (CMU) terminal 4D—Auxiliary jack/USB port/SD card slot hub terminal 2D

• Auxiliary jack/USB port/SD card slot hub malfunction

• Connectivity master unit (CMU) malfunction

Step

Inspection

Action

1

• Switch the ignition off.

• Disconnect the negative battery cable.

  (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

• Disconnect the auxiliary jack/USB port/SD card slot hub connector.

• Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.

• Is the connector normal?

Yes

Go to the next step.

No

Repair or replace the connector, then go to Step 5.

2

• Disconnect the connectivity master unit (CMU) connector.

• Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.

• Is the connector normal?

Yes

Go to the next step.

No

Repair or replace the connector, then go to Step 5.

3

• Verify that the auxiliary jack/USB port/SD card slot hub connector and the connectivity master unit (CMU) connector are disconnected.

• Inspect for continuity between the following terminals (wiring harness-side):

• Connectivity master unit (CMU) terminal 4B—Auxiliary jack/USB port/SD card slot hub terminal 2B

• Connectivity master unit (CMU) terminal 4D—Auxiliary jack/USB port/SD card slot hub terminal 2D

• Is there continuity?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify if there is a common connector between the following terminals:

• Connectivity master unit (CMU) terminal 4B—Auxiliary jack/USB port/SD card slot hub terminal 2B

• Connectivity master unit (CMU) terminal 4D—Auxiliary jack/USB port/SD card slot hub terminal 2D

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has an open circuit.

Go to Step 5.

4

• Always reconnect all disconnected connectors.

• Connect the negative battery cable.

  (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

• Clear the DTC for the connectivity master unit (CMU) using the M-MDS.

  (See CLEARING DTC [CONNECTIVITY MASTER UNIT].)

• Switch the ignition ON (engine off or on) and wait for 7 s or more.

• Retrieve the connectivity master unit (CMU) DTCs using the M-MDS.

  (See DTC INSPECTION [CONNECTIVITY MASTER UNIT].)

• Is the same DTC displayed?

Yes

Replace the auxiliary jack/USB port/SD card slot hub, then go to the next step.

(See AUXILIARY JACK/USB PORT/SD CARD SLOT HUB REMOVAL/INSTALLATION.)

No

Go to Step 6.

5

• Always reconnect all disconnected connectors.

• Connect the negative battery cable.

  (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

• Clear the DTC for the connectivity master unit (CMU) using the M-MDS.

  (See CLEARING DTC [CONNECTIVITY MASTER UNIT].)

• Switch the ignition ON (engine off or on) and wait for 7 s or more.

• Retrieve the connectivity master unit (CMU) DTCs using the M-MDS.

  (See DTC INSPECTION [CONNECTIVITY MASTER UNIT].)

• Is the same DTC displayed?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the connectivity master unit (CMU).

  (See CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION.)

Go to the next step.

No

Go to the next step.

6

• Are any other DTCs displayed?

Yes

Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.

(See DTC TABLE [CONNECTIVITY MASTER UNIT].)

No

DTC troubleshooting completed.