Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC INSPECTION [INSTRUMENT CLUSTER]

< Previous Next >

2016 – MX-5 – Body and Accessories

DTC INSPECTION [INSTRUMENT CLUSTER]

CMDTC Self Test

1. Connect the M-MDS to the DLC-2.

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

a. Select “Self Test”.

b. Select “All CMDTCs”.

3. Verify the DTC according to the directions on the screen.

  • If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection after recording the snapshot data. (See DTC TABLE [INSTRUMENT CLUSTER].)

4. After completion of repairs, clear all DTCs stored in the instrument cluster. (See CLEARING DTC [INSTRUMENT CLUSTER].)

ODDTC Self Test

1. Connect the M-MDS to the DLC-2.

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

a. Select “Self Test”.

b. Select “Modules”.

c. Select “IC”.

3. Verify the DTC according to the directions on the screen.

  • If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection after recording the snapshot data. (See DTC TABLE [INSTRUMENT CLUSTER].)

4. After completion of repairs, clear all DTCs stored in the instrument cluster. (See CLEARING DTC [INSTRUMENT CLUSTER].)

Snapshot Data

  • The data for all DTCs currently detected is stored.

—: Not applicable

Snapshot data item

Unit

Data contents

Data read/use method

Corresponding data monitor items

AAT

°C

°F

Ambient temperature

APP_STATUS

Accelerator Pedal Off/Under20%/Over20%/FAIL

Accelerator pedal position status

CFG_STATUS

Config Complete/Not Configured/Config Error

Instrument cluster configuration status

ECT_STATUS

Under 0 degrees C/0 – Under 80 degrees C/Over 80 degrees C/FAIL

Engine coolant temperature status

IC_VPWR

V

Instrument cluster power supply voltage

When DTC is detected, instrument cluster displays power supply voltage value of instrument cluster in M-MDS.

VPWR

IG-ON_TIMER

hh:mm:ss*1

Elapsed time since ignition was switched ON (engine off or on)

NOTE:

  • The instrument cluster records the elapsed time since the ignition was switched ON (engine off or on).

When DTC is detected, instrument cluster displays elapsed time since ignition was switched ON (engine off or on) in M-MDS.

PWR_MODE_KEY

Key Out/Key Recently Out (Position 0)/Accessory (Position 1)/Post Ignition (Position 2)/Ignition On (Position 2)/Running (Position 2)/Running – Starting

  • Key Out: Ignition switched off

  • Key Recently Out (Position 0): Elapsed time within 3 s since ignition was switched off

  • Accessory (Position 1): Ignition is switched to ACC

  • Post Ignition (Position 2): Elapsed time within 3 s since ignition was switched ON (engine off or on)

  • Ignition On (Position 2): Ignition switched ON (engine off)

  • Running (Position 2): Ignition switched ON (engine on)

  • Running – Starting: Cranking condition

When DTC is detected, instrument cluster displays ignition switch status in M-MDS.

RPM_STATUS

Engine Stop/Under1500rpm/Over1500rpm/FAIL

Engine speed status

When DTC is detected, instrument cluster displays engine speed in M-MDS.

TACHOMTR

SHIFT_STATUS

P/N/D/R/FAIL

Selector lever position status

When DTC is detected, instrument cluster displays selector lever position in M-MDS.

TOTAL_DIST

km

Miles

Accumulated total traveled distance from completion of vehicle until instrument cluster detects DTC (Odometer value in instrument cluster)

The total traveled distance from which the instrument cluster detects DTCs to the present can be calculated by performing the following procedure.

  • Verify the odometer value in the instrument cluster.

  • Verify the snapshot data item TOTAL_DIST.

  • Subtract 2 from 1.

TOTAL_TIME

hh:mm:ss*1

Accumulated total elapsed time since vehicle completion until instrument cluster detects a DTC

NOTE:

  • When the ROOM fuse is removed, and the ignition is switched off, the time is not included in the elapsed time.

The elapsed time from which the instrument cluster detects DTCs to the present can be calculated by performing the following procedure.

  • Verify the instrument cluster PID item TOTAL_TIME.

  • Verify the snapshot data item TOTAL_TIME.

  • Subtract 2 from 1.

TOTAL_TIME

VPWR

V

Instrument cluster power supply voltage

VPWR

VSPD_STATUS

Stop/0-10km/h/Over10km/h/FAIL

Vehicle speed status

When DTC is detected, instrument cluster displays vehicle speed in M-MDS.

SPEEDOMTR

*1
The seconds may be indicated after the decimal point.

< Previous Next >

© 2014 Mazda North American Operations, U.S.A.