| 1. |
Troubleshooting for Speaker
| (1) |
Basic inspection of speaker
Inspect the sound from speaker after
verifying that the speaker mounting screws are removed and the
wiring connector is connected to remove any possible vibration
transmitted from body trims and surrounding
parts.
|
| (2) |
Case Troubleshooting
No.
|
Case
|
Inspection/Remedy
|
1
|
Trembling sound
|
| 1. |
Before replacing the
speaker, inspect that the mounting screw is
installed
normally. |
| 2. |
After re-installing the
speaker, verify that no trembling sound is
heard. |
| 3. |
When hearing a trembling
sound again, replace the speaker with new
one. | |
2
|
Noise
|
| 1. |
Check if the wiring
connector is connected normally. If not, reconnect
the wiring
connector. |
| 2. |
In case of radio static,
check if there is a noise from
CD. |
| 3. |
If a noise is heard with the
radio and CD on, replace the speaker with new
one. |
|
In case there is only radio
static, this causes from poor radio reception.
Thus the speaker needs no repair and
replacement. | |
3
|
Speaker
inoperative
|
Inspection of the wiring connection between
the battery and the speaker
| 1. |
Before replacing the
speaker, inspect the wiring connection between the
battery and the speaker is
normal. |
| 2. |
Check the supply power to
the speaker and the resistance, then inspect the
sound quality.
■ Specified impedance : 2 ~
4Ω
|
| 3. |
If the speaker works poorly,
replace it with new
one. | |
|
When handling the
speakers:
| - |
Do not damage the speaker
with impact, like dropping or throwing
it. |
| - |
Be careful not to drop water
and oil on the
speakers. |
| - |
Caution during handling of
speaker because the material of diaphragm is paper
which is easily torn by impact or external
force. |
| - |
Modifying the audio system
may cause damage to the speakers. If this is the
case, the speakers are not covered by the
manufacturer's
warranty. | | | |
Front Speaker
| 1. |
Remove the front door trim panel and speaker
connector.
(Refer to the BD group - "Front
door") |
| 2. |
Remove the front speaker (A) after loosening 4
rivets.
|
Rear Speaker (Right)
| 1. |
Remove the rear door trim panel and speaker
connector.
(Refer to the BD group - "Interior
trim") |
| 2. |
Remove the rear speaker (A) after removing 4
rivets.
|
Rear Speaker (Left)
| 1. |
Remove the rear door trim panel and speaker
connector.
(Refer to the BD group - "Interior
trim") |
| 2. |
Remove the rear speaker (A) after removing 4
bolts.
|
Center Speaker
| 1. |
Remove the crash pad upper speaker cover
(A).
|
| 2. |
Disconnect the connector, after loosening 2
screws then remove the center speaker (A).
|
Midrange Speaker
| 1. |
Remove the front door trim panel and speaker
connector.
(Refer to the BD group - "Front
door") |
| 2. |
Remove the front midrange speaker, after
loosening 2 screws.
|
Subwoofer Speaker
| 1. |
Remove the rear fillar trim panel and speaker
connector.
(Refer to the BD group - "Interior
trim") |
| 2. |
Remove the subwoofer speaker (A), after
loosening 2 bolts and 2 nuts.
|
Front Speaker
| 1. |
Install the front
speaker. |
| 2. |
Insatll the rivets and connect the
connector. |
| 3. |
Install the front door trim
panel. |
Rear Speaker (Right)
| 1. |
Install the rear
speaker. |
| 2. |
Install the rivets and connect the
connector. |
| 3. |
Install the door trim
panel. |
Rear Speaker (Left)
| 1. |
Install the rear speaker after connecting the
connector. |
| 2. |
Install the door trim
panel. |
Center Speaker
| 1. |
Install the center speaker after connecting
the connector. |
| 2. |
Install the center speaker
cover. |
Mindrange Speaker
| 1. |
Install the midrange speaker after connecting
the connector. |
| 2. |
Install the front door trim
panel. |
Subwoofer Speaker
| 1. |
Install the subwoofer speaker after connecting
the connector. |
| 2. |
Install the rear fillar trim
panel. | |
