| •
|
Prolonged and repeated contact with
mineral oil will result in the removal of natural fats from
the skin, leading to dryness, irritation and dermatitis. In
addition, used engine oil contains potentially harmful
contaminants which may cause skin cancer.
|
| •
|
Exercise caution in order to minimize
the length and frequency of contact of your skin to used oil.
Wear protective clothing and gloves. Wash your skin thoroughly
with soap and water, or use water-less hand cleaner, to remove
any used engine oil. Do not use gasoline, thinners, or
solvents. |
| •
|
In order to preserve the environment,
used oil and used oil filter must be disposed of only at
designated disposal
sites. | |
| 1. |
Drain the engine oil.
| (1) |
Remove the oil filler
cap. |
| (2) |
Remove the oil drain plug, and drain the
oil into a container.
| |
| 2. |
Remove the oil filter(A) with the
SST(09263-2E000, the oil filter wrench).
| (1) |
Remove the oil filter.
|
| (2) |
Check and clean the oil filter
installation surface. |
| (3) |
Check the part number of the new oil
filter is as same as old one. |
| (4) |
Apply clean engine oil to the gasket of
a new oil filter. |
| (5) |
Lightly screw the oil filter into place,
and tighten it until the gasket contacts the
seat. |
| (6) |
Tighten it with the torque
below.
Tightening torque :
11.8 ~ 15.7N.m (1.2 ~ 1.6kgf.m,
8.7 ~ 11.6lb-ft)
| | |
| 3. |
Refill with engine oil.
| (1) |
Clean and install the oil drain plug
with a new gasket.
Tightening torque :
34.3 ~ 44.1N.m (3.5 ~ 4.5kgf.m,
25.3 ~ 32.5lb-ft)
| |
| (2) |
Fill with fresh engine oil.
Capacity
Total : 4.9 L (1.29 U.S.gal., 5.17
U.S.qt., 4.30 lmp.qt.)
Oil pan : 4.2 L (1.10 U.S.gal.,
4.43 U.S.qt., 1.10 lmp.qt.)
Drain and refill in cluding oil
filter :
4.5 L (1.18 U.S.gal., 4.75
U.S.qt., 3.95 lmp.qt.)
| |
| (3) |
Install the oil filler cap.
| |
| 4. |
Start engine and check for oil
leaks. |
| 5. |
Recheck the engine oil
level. |
Engine Oil
| 1. |
Check the engine oil quality.
Check the oil deterioration, entry of water,
discoloring of thinning.
If the quality is visibly poor, replace the
oil. |
| 2. |
Check the engine oil level.
After warning up the engine and then 5 minutes
after the engine stop, oil level should be between the "L" and "F"
marks in the dipstick.
If low, check for leakage and add oil up to
the "F" mark.
|
Do not fill with engine oil above the
"F" mark. | |
Selection Of Engine Oil
Recommendation
ACEA A5 or
above
SAE viscosity grade :
5W-30, 5W-40
Supplier
|
Product
|
SK
|
ZIC
LD5W-30
|
Chevron
|
KIXX G1
LL
|
Total
|
QUARTZ
HKS G-310
|
QUARTZ
INEO MC3 5W-30
|
Shell
|
HELIX
ULTRA AH-E 5W-30
HELIX ULTRA
5W-40
|
Fuchs
|
TITAN
SUPERSYN LONG LIFE 5W-30/40
|
|
For best performance and maximum protection of
all types of operation, select only those lubricants which
:
| 1. |
Satisfy the requirement of the ACEA
classification. |
| 2. |
Have proper SAE grade number for
expected ambient temperature range.
|
| 3. |
Lubricants that do not have both an SAE
grade number and ACEA service classification on the container
should not be
used. | |
