2019 BP Shop Manual

BP Shop Manual

Menu +

TIGHT CORNER BRAKING EFFECT [i-ACTIV AWD SYSTEM]

TIGHT CORNER BRAKING EFFECT [i-ACTIV AWD SYSTEM]

SM2515133

id0303d4138500

Outline

Troubleshooting item	Tight corner braking
Description	• Brakes seem to be applied during tight cornering while driving very slowly on paved road.
Possible cause	• Because the coupling component locks up easily (similar to direct AWD), rotational difference between the front and rear wheels cannot be absorbed and brake-like phenomenon occurs. • Due to the coupling component construction, slight tight corner braking effect occurs during tight cornering on a paved road. (AWD system is normal. Compare with another same model vehicle to determine malfunction.) • Coupling component malfunction • AWD solenoid malfunction
System wiring diagram	• Not applicable
Connector diagram	• Not applicable

Diagnostic Procedure

Step	Inspection	Results	Action
1	VERIFY DSC HU/CM, PCM, TCM, EPS CONTROL MODULE AND ELECTRICAL SUPPLY UNIT (ESU) DTCs • Verify DSC HU/CM, PCM, TCM, EPS control module and electrical supply unit (ESU) DTCs using the M-MDS. (See DTC INSPECTION.) • Are there any DTCs present?	Yes	Go to applicable DTC inspection. (See DTC TABLE [DSC HU/CM (US)].) (See DTC TABLE [PCM (SKYACTIV-G (US))].) (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [TCM (EV6A-EL, EV6AX-EL) (US)].) (See DTC TABLE [ELECTRIC POWER STEERING (EPS) (US)].) (See DTC TABLE [BODY CONTROL MODULE (BCM) (US)].)
1		No	Go to next step.
2	VERIFY TIRE AIR PRESSURE • Inspect tire air pressure. • Is it within specification?	Yes	Go to next step.
2		No	Adjust tire air pressure, then go to next step.
3	INSPECT ABS WHEEL-SPEED SENSOR • Inspect ABS wheel-speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.) (See REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD].) • Is it normal?	Yes	Go to next step.
3		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION.) (See REAR ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION.)
4	COMPARE WITH SAME MODEL VEHICLE • Perform simulation driving with another same model vehicle. • Does malfunction recur on the same model vehicle?	Yes	i-ACTIV AWD system is normal.
4		No	Go to next step.
5	TRY TO REPRODUCE MALFUNCTION BY DRIVING VEHICLE WITH AWD SOLENOID CONNECTOR DISCONNECTED • Switch the ignition off. • Disconnect the AWD solenoid connector. • Try to reproduce the malfunction by driving the vehicle. • Does the malfunction recur?	Yes	Replace coupling component. (See COUPLING COMPONENT REMOVAL/INSTALLATION [(US)].)
5		No	Go to next step.
6	INSPECT AWD SOLENOID • Inspect AWD solenoid. (See AWD SOLENOID INSPECTION.) • Is AWD solenoid normal?	Yes	Inspect harness between AWD solenoid and electrical supply unit (ESU), then go to next step.
6		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See COUPLING COMPONENT REMOVAL/INSTALLATION [(US)].)
Repair completion verification	VERIFY THAT MALFUNCTION SYMPTOMS DO NOT RECUR AFTER REPAIR • Install/connect the part removed/disconnected during the troubleshooting procedure. • Has the malfunction symptom been eliminated?	Yes	Complete the symptom troubleshooting. Explain to the customer what has been repaired.
Repair completion verification		No	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].) If the CAN communication is normal, perform the diagnosis from Step 1.